Investigation of the Effect of Fin Geometry on the Thermal Performance of Microelectronic Devices

Downloads

Authors

Abstract

This study systematically evaluates the optimal heat sink geometry for enhanced thermal performance in electronic cooling applications. ANSYS-Icepak and COMSOL Multiphysics software assessed four distinct fin geometries (square, rectangular, circular, and conical), all uniformly sized for accurate comparison. Vital performance parameters were analyzed, including maximum temperature reduction, pressure drop, and airflow velocity. These indicators provide a holistic assessment of cooling efficacy and aerodynamic characteristics. The findings highlight the effectiveness of rectangular fins, which significantly reduce maximum temperatures due to their efficient balance of conductive and convective heat transfer. At the same time, conical fins display lower pressure drops and circular fins achieve higher airflow velocities, these attributes do not consistently enhance cooling capabilities. The importance of this study resides in its provision of definitive guidance for selecting fin geometry in designing efficient heat sinks, crucial for electronic devices. This knowledge is particularly vital for developing advanced cooling systems in compact, high-power electronics, underscoring the significant impact of fin geometry on overall thermal management efficiency. Quantitative data supporting these findings are available in the full study.

Keywords:

fin geometry, electronic cooling, heat sink, thermal management, ANSYS-Icepak

References


  1. Luo W. et al., Recent progress in quantum photonic chips for quantum communication and internet, Light: Science & Applications, 12(1): 175, 2023, https://doi.org/10.1038/s41377-023-01173-8

  2. Al-Omari S.A.B., Qureshi Z.A., Elnajjar E., Mahmoud F., A heat sink integrating fins within high thermal conductivity phase change material to cool high heat-flux heat sources, International Journal of Thermal Sciences, 172(Part A): 107190, 2022, https://doi.org/10.1016/j.ijthermalsci.2021.107190

  3. Gaikwad A., Sathe A., Sanap S., A design approach for thermal enhancement in heat sinks using different types of fins: A review, Frontiers in Thermal Engineering, 2: 980985, 2023, https://doi.org/10.3389/fther.2022.980985

  4. Blinov A., Vinnikov D., Lehtla T., Cooling methods for high-power electronic systems, Scientific Journal of Riga Technical University. Power and Electrical Engineering, 29(1): 79–86, 2011, https://doi.org/10.2478/v10144-011-0014-x

  5. Fallahi A., Guldentops G., Tao M., Granados-Focil S., Van Dessel S., Review on solid-solid phase change materials for thermal energy storage: molecular structure and thermal properties, Applied Thermal Engineering, 127: 1427–1441, 2017, https://doi.org/10.1016/j.applthermaleng.2017.08.161

  6. Eivari H.A., Sohbatzadeh Z., Mele P., Assadi M.H.N., Low thermal conductivity: fundamentals and theoretical aspects in thermoelectric applications, Materials Today Energy, 21: 100744, 2021, https://doi.org/10.1016/j.mtener.2021.100744

  7. Yang T., King W.P., Miljkovic N., Phase change material-based thermal energy storage, Cell Reports Physical Science, 2(8): 100540, 2021, https://doi.org/10.1016/j.xcrp.2021.100540

  8. Ben Salah S., Ben Hamida M.B., Alternate PCM with air cavities in LED heat sink for transient thermal management, International Journal of Numerical Methods for Heat & Fluid Flow, 29(11): 4377–4393, 2019, https://doi.org/10.1108/HFF-02-2019-0099

  9. Izadi M., Fagehi H., Imanzadeh A., Altnji S., Bechir Ben Hamida M., Sheremet M.A., Influence of finned charges on melting process performance in a thermal energy storage, Thermal Science and Engineering Progress, 37: 101547, 2023, https://doi.org/10.1016/j.tsep.2022.101547

  10. Ben Hamida M.B., Hajlaoui K., Almeshaal M.A., A 3D numerical analysis using phase change material for cooling circular light emitting diode, Case Studies in Thermal Engineering, 43: 102792, 2023, https://doi.org/10.1016/j.csite.2023.102792

  11. Saravanan V., Hithaish D., Umesh C.K., Seetharamu K.N., Numerical investigation of thermo-hydrodynamic performance of triangular pin fin heat sink using nano-fluids, Thermal Science and Engineering Progress, 21: 100768, 2021, https://doi.org/10.1016/j.tsep.2020.100768

  12. Massoudi M.D., Ben Hamida M.B., Almeshaal M.A., Hajlaoui K., Numerical evaluation of MHD SWCNT-water nanoliquid performance in cooling an electronic heat sink featuring twisted hexagonal fins considering thermal emission impact: comparison between various fins shapes, Sustainable Energy Technologies and Assessments, 53(Part A): 102350, 2022, https://doi.org/10.1016/j.seta.2022.102350

  13. Massoudi M.D., Ben Hamida M.B., Enhancement of MHD radiative CNT-50% water + 50% ethylene glycol nanoliquid performance in cooling an electronic heat sink featuring wavy fins, Waves in Random and Complex Media, 35(6): 11357–11382, 2025, https://doi.org/10.1080/17455030.2022.2122626

  14. Massoudi M.D., Ben Hamida M.B., Almeshaal M.A., Hajlaoui K., Effects of L-shaped fins on cooling an electronic heat sink fitted under magnetic field of CNT–water/ethylene glycol nanoliquid, The European Physical Journal Plus, 137(7): 843, 2022, https://doi.org/10.1140/epjp/s13360-022-03044-4

  15. Ben Hamida M.B., Hatami M., Investigation of heated fins geometries on the heat transfer of a channel filled by hybrid nanofluids under the electric field, Case Studies in Thermal Engineering, 28: 101450, 2021, https://doi.org/10.1016/j.csite.2021.101450

  16. Massoudi M.D., Ben Hamida M.B., Combined impacts of square fins fitted wavy wings and micropolar magnetized-radiative nanofluid on the heat sink performance, Journal of Magnetism and Magnetic Materials, 574: 170655, 2023, https://doi.org/10.1016/j.jmmm.2023.170655

  17. Ben Hamida M.B., Thermal management of square light emitting diode arrays: modeling and parametric analysis, Multidiscipline Modeling in Materials and Structures, 20(2): 363–383, 2024, https://doi.org/10.1108/MMMS-09-2023-0311

  18. Shafeie H., Abouali O., Jafarpur K., Ahmadi G., Numerical study of heat transfer performance of single-phase heat sinks with micro pin-fin structures, Applied Thermal Engineering, 58(1–2): 68–76, 2013, https://doi.org/10.1016/j.applthermaleng.2013.04.008

  19. Yeom T., Simon T., Zhang T., Zhang M., North M., Cui T., Enhanced heat transfer of heat sink channels with micro pin fin roughened walls, International Journal of Heat and Mass Transfer, 92: 617–627, 2016, https://doi.org/10.1016/j.ijheatmasstransfer.2015.09.014

  20. Ambreen T., Saleem A., Park C.W., Numerical analysis of the heat transfer and fluid flow characteristics of a nanofluid-cooled micropin-fin heat sink using the Eulerian-Lagrangian approach, Powder Technology, 345: 509–520, 2019, https://doi.org/10.1016/j.powtec.2019.01.042

  21. Arshad W., Ali H.M., Experimental investigation of heat transfer and pressure drop in a straight minichannel heat sink using TiO2 nanofluid, International Journal of Heat and Mass Transfer, 110: 248–256, 2017, https://doi.org/10.1016/j.ijheatmasstransfer.2017.03.032

  22. Arshad W., Ali H.M., Graphene nanoplatelets nanofluids thermal and hydrodynamic performance on integral fin heat sink, International Journal of Heat and Mass Transfer, 107: 995–1001, 2017, https://doi.org/10.1016/j.ijheatmasstransfer.2016.10.127

  23. Jalil J.M., Reja A.H., Hadi A.M., Numerical investigation of thermal performance of micro-pin fin with different arrangements, [in:] IOP Conference Series: Materials Science and Engineering, 765: 012037, 2020, https://doi.org/10.1016/10.1088/1757-899X/765/1/012037

  24. Ozbalci O., Dogan A., Asilturk M., Heat Transfer performance of plate fin and pin fin heat sinks using Al2O3/H2O nanofluid in electronic cooling, Processes, 10(8): 1644, 2022, https://doi.org/10.3390/pr10081644

  25. Ekpu M., Effect of fins arrangement on thermal performance in microelectronics devices, Journal of Applied Sciences and Environmental Management, 22(11): 1797–1800, 2018, https://doi.org/10.4314/jasem.v22i11.14

  26. Tanda G., Heat transfer and pressure drop in a rectangular channel with diamond-shaped elements, International Journal of Heat and Mass Transfer, 44(18): 3529–3541, 2001, https://doi.org/10.1016/S0017-9310(01)00018-7

  27. Debich B., El Hami A., Yaich A., Gafsi W., Walha L., Haddar M., Design optimization of PCM-based finned heat sinks for mechatronic components: a numerical investigation and parametric study, Journal of Energy Storage, 32: 101960, 2020, https://doi.org/10.1016/j.est.2020.101960

  28. Ali H.M. et al., Advances in thermal energy storage: fundamentals and applications, Progress in Energy and Combustion Science, 100: 101109, 2024, https://doi.org/10.1016/j.pecs.2023.101109

  29. Shatikian V., Ziskind G., Letan R., Numerical investigation of a PCM-based heat sink with internal fins, International Journal of Heat and Mass Transfer, 48(17): 3689–3706, 2005, https://doi.org/10.1016/j.ijheatmasstransfer.2004.10.042

  30. Jaworski M., Thermal performance of heat spreader for electronics cooling with incorporated phase change material, Applied Thermal Engineering, 35: 212–219, 2012, https://doi.org/10.1016/j.applthermaleng.2011.10.036

  31. Kamkari B., Shokouhmand H., Experimental investigation of phase change material melting in rectangular enclosures with horizontal partial fins, International Journal of Heat and Mass Transfer, 78: 839–851, 2014, https://doi.org/10.1016/j.ijheatmasstransfer.2014.07.056

  32. Pakrouh R., Hosseini M.J., Ranjbar A.A., Bahrampoury R., A numerical method for PCM-based pin fin heat sinks optimization, Energy Conversion and Management, 103: 542–552, 2015, https://doi.org/10.1016/j.enconman.2015.07.003

  33. Bondareva N.S., Sheremet M.A., 3D natural convection melting in a cubical cavity with a heat source, International Journal of Thermal Sciences, 115: 43–53, 2017, https://doi.org/10.1016/j.ijthermalsci.2017.01.021

  34. Ali H.M., Ashraf M.J., Giovannelli A., Ifran M., Irshad T.B., Hamid H.M., Hassan F., Arshad A., Thermal management of electronics: an experimental analysis of triangular, rectangular and circular pin-fin heat sinks for various PCMs, International Journal of Heat and Mass Transfer, 123: 272–284, 2018, https://doi.org/10.1016/j.ijheatmasstransfer.2018.02.044

  35. Senthilkumar R., Prabhu S., Cheralathan M., Experimental investigation on carbon nano tubes coated brass rectangular extended surfaces, Applied Thermal Engineering, 50(1): 1361–1368, 2013, https://doi.org/10.1016/j.applthermaleng.2012.05.040

  36. Ji C., Qin Z., Dubey S., Choo F.H., Duan F., Simulation on PCM melting enhancement with double-fin length arrangements in a rectangular enclosure induced by natural convection, International Journal of Heat and Mass Transfer, 127(Part C): 255–265, 2018, https://doi.org/10.1016/j.ijheatmasstransfer.2018.07.118

  37. Xie J., Choo K.F., Xiang J., Lee H.M., Characterization of natural convection in a PCM-based heat sink with novel conductive structures, International Communications in Heat and Mass Transfer, 108: 104306, 2019, https://doi.org/10.1016/j.icheatmasstransfer.2019.104306

  38. Yaseen S.J., Radhi Z.K., Natoosh R.L., Al-Sabur R., Homod R.Z., Mohammed H.I., A computational search for the optimal microelectronic heat sink using ANSYS Icepak, International Journal of Thermofluids, 23: 100759, 2024, https://doi.org/10.1016/j.ijft.2024.100759

  39. Rosli R., Mohd Annuar K.A., Ismail F.S., Optimal pin fin heat sink arrangement for solving thermal distribution problem, Journal of Advanced Research in Fluid Mechanics and Thermal Sciences, 11(1): 1–18, 2015.

  40. Yaseen S.J., Numerical study of the fluid flow and heat transfer in a finned heat sink using Ansys Icepak, Open Engineering, 13(1): 20220440, 2023, https://doi.org/10.1515/eng-2022-0440

  41. Al-Saad M., Yassen S.J., Suarez-Afanador C., AlShara A.K., Chamkha A.J., Simulation of blood flow in human arteries as porous media, Waves in Random and Complex Media, 36(1): 1192–1202, 2026, https://doi.org/10.1080/17455030.2022.2162151

  42. Radhi Z.K., Yaseen S.J., Alsahlani A.A., Al-Sabu R., Exploring magnetohydrodynamic influence on mixed convection within a vented enclosure containing a heat-conductive square column, International Journal of Mechanical Engineering and Robotics Research, 13(1): 75–84, 2024, https://doi.org/10.18178/ijmerr.13.1.75-84

  43. Adhikari R.C., Wood D.H., Pahlevani M., An experimental and numerical study of forced convection heat transfer from rectangular fins at low Reynolds numbers, International Journal of Heat and Mass Transfer, 163: 120418, 2020, https://doi.org/10.1016/j.ijheatmasstransfer.2020.120418

  44. Hu W.L., Ma A.J., Guan Y., Cui Z.J., Zhang Y.B., Wang J., Experimental study of the air side performance of fin-and-tube heat exchanger with different fin material in dehumidifying conditions, Energies, 14(21): 7030, 2021, https://doi.org/10.3390/en14217030

  45. Wei W., Xu G., Wang Y., Ding E., Study on air-side performance of air-cooled heat exchangers under large air velocity and wet conditions, Thermal Science and Engineering Progress, 48: 102389, 2024, https://doi.org/10.1016/j.tsep.2024.102389

  46. Watban Khalid Fahmi A.T., Reza Kashyzadeh K., Ghorbani S., A comprehensive review on mechanical failures cause vibration in the gas turbine of combined cycle power plants, Engineering Failure Analysis, 134: 106094, 2022, https://doi.org/10.1016/j.engfailanal.2022.106094