Engineering Transactions, 43, 1-2, pp. 327-355, 1995

The 18G2A Steel (Construction Steel) Cyclic Behaviour in the Case of Complex Uniaxial Loading

E. Sender
Institute of Fundamental Technological Research, Warszawa
Poland

W. Trąmpczyński
Institute of Fundamental Technological Research, Warszawa
Poland

This paper is concerned with the phenomenon of uniaxial cyclic material behaviour in the plastic range. A set of systematic strain and stress-controlled cyclic (tension-compression) experiments was conducted on round bar specimens made of 18G2A (heat treated) construction steel at room temperature. Results concerning monotonic loading, straincontrolled symmetric cyclic loading and stress-controlled non-symmetric cyclic loading (ratchetting) are presented and summarized. All experiments were performed on similar specimens, the same laboratory equipment and using the same experimental technique. The technique of successive unloadings (proposed by the author [1,2]) was used to obtain some additional information concerning the yield surface position and its evolution for the loading programs mentioned above.

Full Text: PDF

References

TH. LEHMANN, B. RANIECKI and W. TRĄMPCZYŃSKI, The Bauschinger effect in cyclic plasticity, Arch. Mech., 37, 6, pp. 643-659, 1985.

W. TRĄMPCZYŃSKI, On a simple experimental technique for the yield surface determination, Bull. Acad. Polon. Sci., Série Sci. Tech., 37, 7-12, pp. 407-4181 1989.

R. LANDGRAF, J. MORROW and T. ENDO, Determination of cyclic stress-strain curve, J. Materials, 4,176, 1969.

H. JHANSALE, A new parameter for the hysteresis stress-strain behavior of metals, ASME J. Engng. Materials and Technology, 97, 33, 1975.

M. ŚLIWOWSKI, Behavior of stress-strain diagrams for cyclic loading, Bull. Acad. Polon Sci., Série Sci. Tech., 27, 115-123, 1979.

Y. OHASHI, M. KAWAI and T. KAITO, lnelastic behavior of type 316 stainless steel, J. Engng., Mat. Techn., ASME, 111, 278-285, 1985.

A. BENALLAL and D. MARQUIS, An experimental investigation of cyclic hardening of 316 stainless steel under complex multiaxial loadings, Trans. of 9th SMIRT Conf., Vol. L, 345-356, 1987,

M. OHNAMI, M. SAKANE and S. NISHINO, Cyclic behavior of type 304 stainless steel in biaxial stress states at elevated temperatures, Int. J. Plasticity, 4, 77-89, 1988.

H. ISHIKAWA and K. SASAKI, Stress strain relations of SUS304 stainless steel alter cyclic preloading, 1. Engng. Mat. and Techn., vol. III, 417-423, 1989.

T. HASSAN and S. KYRIAKIDES, Ratcheting in cyclic plasticity, Part I. Uniaxial behavior, Int. J. Plasticity, 8, 91-116, 1992.

T. HASSAN, E. CORONA and S. KYRIAKIDES, Ratcheting in cyclic plasticity, Part Il. Multiaxial behavior, Int. J. Plasticity, 8, 117-146, 1992.

Z. MRÓZ, On generalized kinematic hardening rule with memory of maximal prestress, J. Mech. Appl., 5, 242-260, 1981.

Y. DAFALIAS, A novel bounding surface constitutive law for the monotonic and cyclic har4ening response of metals, 6th SMIRT Conference, 1981.

N. OHNO, A constitutive model of cyclic plasticity with a nonhardening strain region, J. Appl. Mech, 49, 721-727, 1982.

TH. LEHMANN, General frame for the definition of constitutive laws for large nonisothermic elastic-plastic and elastic-visco-plastic deformation, The Constitutive Law in Thermoplasticity, CISM, 1984.

Y. DAFALIAS, Modelling cyclic plasticity. Simplicity versus sophistication, Mechanics of Engineering Materials, C. DESAI and R. GALLAGHER [Eds.], John Willey and Sons, New York, p. 153, 1984.

K. VALANIS and C. LEE, Endochronic plasticity. Physical basis and applications, Mechanics of Engineering Materials, C. DESAI and R. GALLAGHER [Eds.], John Willey and Sons, New York, p. 591, 1984.

D.L. MCDOWELL, An experimental study of the structure of constitutive equations for non-proportional cyclic plasticity, ASME J. Engng. Mat. Techn., 107, 307-315, 1985.

J. CHABOCHE, Time independent constitutive theories for cyclic plasticity, Int. J. Plasticity, 2, 149, 1986.

N. OHNO and Y. KACHI, A constitutive model of cyclic plasticity for non-linear hardening materials, J. Appl. Meck., 53, 395-403, 1986.

H. ISHIKAWA and K. SASAKI, Constitutive modelling of cyclic plasticity considering induced anisotropy, Constitutive Laws for Engineering Materials, C.S. DESAI et al. [Eds.], Elsevier, pp. 581-583, 1987.

D.L. MCDOWELL, Simple experimentally motivated cyclic plasticity model, ASCE J. Engng. Mech., 113, 378, 1987.

J. CHABOCHE and D. NOUAILHAS, Constitutive modelling of ratchetting effects. Part I. Experimental facts and properties of classical models, ASME J. Engng. Material and Technology, 111, 384, 1989.

J. CHABOCHE and D. NOUAILHAS, Constitutive modelling of ratchetting effects. Part II. Possibilities of some additional kinematic rules, ASME J. Engng. Materiał and Technology, 111, 384, 1989.

F. ELLYIN and Z. XIA, A rate-independent constitutive model for transient nonproportional loading, J. Mech. Phys. Solids, 37, 1, pp. 71-91, 1989.

N. OHNO, Recent topics in constitutive modelling of cyclic plasticity and viscoplasticity, ASME Appl. Mech. Revs., 43, 11, 283-295, 1990.

W. TRĄMPCZYŃSKI and Z. MRÓZ, Anisotropic hardening model and its application to cyclic loading, [in:] Anisotropy and Localisation of Plastic Deformation, Proc. of Plasticity 91, J.P. BOEHLER and A.S. KHAN [Eds.], Elsevier Applied Science, 1991.

W. TRĄMPCZYŃSKI, The experimental verification of the evolution of kinematic and isotropic hardening in cyclic plasticity, J. Mech. Phys. Solids, 36, 4, pp. 417-441, 1988.




Copyright © 2014 by Institute of Fundamental Technological Research
Polish Academy of Sciences, Warsaw, Poland